Forget to add a bunch of things

oops

1 files changed, 0 insertions, 93 deletions

diff --git a/HW3.X/strap012_hw3prob2.c b/HW3.X/strap012_hw3prob2.c
deleted file mode 100644
index 6071e56..0000000
--- a/HW3.X/strap012_hw3prob2.c
+++ /dev/null
@@ -1,93 +0,0 @@
-#include <xc.h>
-
-// PIC24FJ64GA002 Configuration Bit Settings
-// 'C' source line config statements
-
-// CONFIG2
-#pragma config POSCMOD = NONE           // Primary Oscillator Select (Primary oscillator disabled)
-#pragma config I2C1SEL = PRI            // I2C1 Pin Location Select (Use default SCL1/SDA1 pins)
-#pragma config IOL1WAY = OFF            // IOLOCK Protection (IOLOCK may be changed via unlocking seq)
-#pragma config OSCIOFNC = OFF           // Primary Oscillator Output Function (OSC2/CLKO/RC15 functions as CLKO (FOSC/2))
-#pragma config FCKSM = CSECME           // Clock Switching and Monitor (Clock switching is enabled, Fail-Safe Clock Monitor is enabled)
-#pragma config FNOSC = FRCPLL           // Oscillator Select (Fast RC Oscillator with PLL module (FRCPLL))
-#pragma config SOSCSEL = SOSC           // Sec Oscillator Select (Default Secondary Oscillator (SOSC))
-#pragma config WUTSEL = LEG             // Wake-up timer Select (Legacy Wake-up Timer)
-#pragma config IESO = ON                // Internal External Switch Over Mode (IESO mode (Two-Speed Start-up) enabled)
-
-// CONFIG1
-#pragma config WDTPS = PS32768          // Watchdog Timer Postscaler (1:32,768)
-#pragma config FWPSA = PR128            // WDT Prescaler (Prescaler ratio of 1:128)
-#pragma config WINDIS = ON              // Watchdog Timer Window (Standard Watchdog Timer enabled,(Windowed-mode is disabled))
-#pragma config FWDTEN = OFF             // Watchdog Timer Enable (Watchdog Timer is disabled)
-#pragma config ICS = PGx1               // Comm Channel Select (Emulator EMUC1/EMUD1 pins are shared with PGC1/PGD1)
-#pragma config GWRP = OFF               // General Code Segment Write Protect (Writes to program memory are allowed)
-#pragma config GCP = OFF                // General Code Segment Code Protect (Code protection is disabled)
-#pragma config JTAGEN = OFF             // JTAG Port Enable (JTAG port is disabled)
-
-// This program measures the duty cycle (i.e., duration of a signal being 1) in
-// terms of num cycles.
-// INT0 pin has the external sig. T1 counts #cycles.
-// Both programmed as interrupts.
-
-volatile unsigned int overflow = 0;
-volatile unsigned long int numCycles = 0;  // duty cycle in terms of # TCY
-volatile unsigned int high = 0, low = 0;
-
-void __attribute__((__interrupt__,__auto_psv__)) _T1Interrupt(void)
-{
-    IFS0bits.T1IF = 0;
-    overflow++;
-}
-
-void __attribute__((__interrupt__,__auto_psv__)) _INT0Interrupt(void)
-{
-    _INT0IF = 0;
-
-    if (_INT0EP == 0){   // I was waiting for a rising edge
-        TMR1 = 0;
-        overflow = 0;
-    } else { // I was waiting for a falling edge
-        numCycles = TMR1 + 16000L * overflow;
-//        TMR1 = 0;         // uncomment these two lines if you want the period
-//        overflow = 0;     //       and not just active duty cycle. also
-                            //       delete the if part, and the last line
-                            //       that changes polarity of INT0EP
-    }
-
-    _INT0EP = 1 - _INT0EP;
-    
-}
-
-void setup(void)
-{
-    CLKDIVbits.RCDIV = 0; // make 16MHz
-    // setup INT0 (RB7) pin as input
-    AD1PCFG = 0x9fff;
-    LATBbits.LATB7 = 1;
-
-    T1CON = 0;
-    PR1 = 15999;
-    TMR1 = 0;
-    T1CONbits.TON = 1;
-
-    IFS0bits.T1IF = 0;
-    //IPC0bits.T1IP = 4;
-    /* enable Timer 1 interrupt */
-    IEC0bits.T1IE = 1;
-
-    _INT0EP = 0;
-    _INT0IF = 0;
-    _INT0IE = 1;
-
-}
-
-
-int main(void)
-{
-
-    setup();
-    int edge = 0;
-    while (1) {
-
-    }
-}