1 files changed, 0 insertions, 77 deletions
diff --git a/HW3.X/strap012_hw3prob3.c b/HW3.X/strap012_hw3prob3.c
deleted file mode 100644
index 6f3b6b2..0000000
--- a/HW3.X/strap012_hw3prob3.c
+++ /dev/null
@@ -1,77 +0,0 @@
-#include <xc.h>
-
-// PIC24FJ64GA002 Configuration Bit Settings
-
-// CONFIG2
-#pragma config POSCMOD = NONE           // Primary Oscillator Select (Primary oscillator disabled)
-#pragma config I2C1SEL = PRI            // I2C1 Pin Location Select (Use default SCL1/SDA1 pins)
-#pragma config IOL1WAY = OFF            // IOLOCK Protection (IOLOCK may be changed via unlocking seq)
-#pragma config OSCIOFNC = OFF           // Primary Oscillator Output Function (OSC2/CLKO/RC15 functions as CLKO (FOSC/2))
-#pragma config FCKSM = CSECME           // Clock Switching and Monitor (Clock switching is enabled, Fail-Safe Clock Monitor is enabled)
-#pragma config FNOSC = FRCPLL           // Oscillator Select (Fast RC Oscillator with PLL module (FRCPLL))
-#pragma config SOSCSEL = SOSC           // Sec Oscillator Select (Default Secondary Oscillator (SOSC))
-#pragma config WUTSEL = LEG             // Wake-up timer Select (Legacy Wake-up Timer)
-#pragma config IESO = ON                // Internal External Switch Over Mode (IESO mode (Two-Speed Start-up) enabled)
-
-// CONFIG1
-#pragma config WDTPS = PS32768          // Watchdog Timer Postscaler (1:32,768)
-#pragma config FWPSA = PR128            // WDT Prescaler (Prescaler ratio of 1:128)
-#pragma config WINDIS = ON              // Watchdog Timer Window (Standard Watchdog Timer enabled,(Windowed-mode is disabled))
-#pragma config FWDTEN = OFF             // Watchdog Timer Enable (Watchdog Timer is disabled)
-#pragma config ICS = PGx1               // Comm Channel Select (Emulator EMUC1/EMUD1 pins are shared with PGC1/PGD1)
-#pragma config GWRP = OFF               // General Code Segment Write Protect (Writes to program memory are allowed)
-#pragma config GCP = OFF                // General Code Segment Code Protect (Code protection is disabled)
-#pragma config JTAGEN = OFF             // JTAG Port Enable (JTAG port is disabled)
-
-// To test: Window > Simulator > Stimulus. Click on the Pin / Register Actions.
-// Click on the top row where it says "Click here to add/remove signals", and add IC1
-// (or RB6). Add entries that change the signal to 1 at time 1000, to zero at 1100, and so on.
-// You may want to check the checkbox that says "Repeat from action".
-
-volatile unsigned int dutyCycle = 0;  // positive or negative
-
-void __attribute__((__interrupt__,__auto_psv__)) _IC1Interrupt(void)
-{
-    static unsigned int last = 0;
-    unsigned int current;
-    _IC1IF = 0;
-    
-    current = IC1BUF;
-    if (current > last)
-        dutyCycle = current - last;
-    else
-//        dutyCycle = ((long)(1<<16) + current) - last;
-        dutyCycle = ((long)(PR3+1) + current) - last;
-    
-    last = current;
-}
-
-void setup()
-{
-    CLKDIVbits.RCDIV = 0;
-    AD1PCFG = 0x9fff;  // For digital I/O.  If you want to use analog, you'll
-                       // need to change this.
-    _TRISB6 = 1;
-    __builtin_write_OSCCONL(OSCCON & 0xbf); // unlock PPS
-    _IC1R = 6 ;   //IC! <- RB6; See Table 10-2 on P108 of the datasheet
-    __builtin_write_OSCCONL(OSCCON | 0x40); // lock   PPS
-
-    T3CON = 0;
-    PR3 = 65535;
-    TMR3 = 0;
-    _T3IF = 0;
-    T3CON = 0x8000;
-
-    IC1CON = 1; // every edge
-    _IC1IF = 0;
-    _IC1IE = 1;
-}
-
-int main(void)
-{
-    setup();
-
-    while (1){
- 
-    }
-}